Easy

VAV terminal unit Type TVR/160/Easy

VAV terminal unit type TVR with an Easy controller

EASY

For easy adjustment

Control components for VAV terminal units, to be mounted on the terminal unit for easy operation

Simplified ordering and on-site assignment to rooms as selection is based on the nominal size of the duct
Simple volume flow rate setting without additional device
Indicator light simplifies functional checking
With push button for triggering a function test
Proven technology of the Compact volume flow controllers
Suitable for constant and variable volume flow rates and q_vmin-, q_vmax-Switching

General Information

Application

All-in-one control devices for VAV terminal units
Dynamic effective pressure transducer, electronic controller and actuator are fitted together in one casing
For use with clean air only
Standard filtration in comfort conditioning systems allows for use of the controller in the supply air without additional dust protection
Choice of various control options based on setpoint value default setting
Volume flow rate control is based on setpoint values received from room temperature controller, central BMS, air quality controller or other devices as an analogue signal.
Override control for activating q_vmin, q_vmax, shut-off or OPEN position can be set with a switch or relay
The volume flow rate actual value is available as a linear voltage signal

With heavy dust levels in the room

Install suitable extract air filters upstream, as a partial volume flow is routed through the transducer for volume flow rate measurement

If the air is contaminated with fluff, sticky components or aggressive substances

Do not use an Easy controller

Construction

LMV-D3AL-F TR for LVC
TR0VE-024T-05I-DD15 for TVE
LMV-D3A-F TR for TVR
LMV-D3A TR for TZ-Silenzio, TA-Silenzio, TVZ, TVA
227V-024T-05-002 for TVR
227V-024T-05-002/RE20 for TZ-Silenzio, TA-Silenzio, TVZ, TVA
227V-024T-15-002 for TVJ, TVT up to 1000 x 600
SMV-D3A TR for TVT from 1000 x 600

Parts and characteristics

Transducer for dynamic measurements
Mechanical stops for limiting the damper blade positions (not for TVE)
Actuators with overload protection
Transparent protective cap or terminal cover (TVE)

Interface

Analogue signal 0 – 10 V DC

Control strategy

The volume flow controller works independent of the duct pressure
Differential pressure fluctuations do not result in permanent volume flow rate changes
To prevent the control from becoming unstable, a dead band is allowed within which the damper blade does not move
The factory set volume flow rate parameters can be altered by the customer

Operating modes

Operating mode variable volume flow rate, q_vmin: Minimum volume flow rate, q_vmax: Maximum volume flow rate
Operating mode Constant value, q_vmin: Constant volume flow rate, q_vmax: 100 %

Commissioning

Operating values q_vmin, q_vmaxto be set on site with potentiometer on the outside of the housing without additional adjustment tools

Technical information

Function, Technical data, Order code

Principle of operation – LVC, TVR, TZ-Silenzio, TA-Silenzio, TVZ, TVA, TVJ, TVT

① Effective pressure transducer

② Actuator

③ Volume flow controller

④ Setpoint value signal

A closed control circuit for regulation of the volume flow rate, i.e. measuring - comparing - adjusting, is characteristic of air terminal units.
The volume flow rate is measured by measuring a differential pressure (effective pressure). This is done via a differential pressure sensor. An integrated differential pressure transducer converts the effective pressure into a voltage signal. The volume flow rate actual value is hence available as a voltage signal. The factory setting is such that 10 V DC always corresponds to the nominal volume flow rate (q_vnom).
The volume flow rate setpoint value comes from a higher-level controller (e.g. room temperature controller, air quality controller, central BMS) or from switch contacts. Variable volume flow control results in a value between q_vmin and q_vmax. It is possible to override the room temperature control, e.g. by a complete shut-off of the duct.
The controller compares the volume flow rate setpoint value to the actual value and controls the integral actuator accordingly.
Flow rate parameter q_vmin and q_vmax can be set on potentiometers.

Category

Type Easy volume flow rate controller with potentiometers to set q_vmin, q_vmax

Application

Control of a constant or variable volume flow rate setpoint.
Electronic controller for applying a reference value and capturing an actual value signal.
The actual value signal relates to the nominal volume flow rate so that commissioning and subsequent adjustment are simplified
Stand-alone operation or integration with a central BMS.

Area of application

Dynamic transducer for clean air in ventilation and air conditioning systems

Actuator

Integral; slow running (running time 100 – 270s for 90°)

Installation orientation

Either direction

Connection

Double terminal for supply voltage to connect up to 3 controllers
No junction box required.

Supply voltage

24 V AC/DC

Interface/signalling

Analogue signal 0 – 10 V DC

Interface information

Volume flow rate setpoint value and actual value
The actual value signal relates to the nominal volume flow rate so that commissioning and subsequent adjustment are simplified

Special functions

Clearly visible external indicator light for signalling the functions: Set, not set, and power failure
Activation of Vmin, Vmax, Closed and Open, by means of external switch contacts

Parameter setting

Parameters specific to the VAV terminal unit are factory set
Vmin and Vmax can be set by others using the potentiometers on the outside of the casing, no tools required

Factory condition

Electronic controller is factory mounted on the control unit
Factory-set parameters
Functional test with air (see sticker)

TVR mit der Anbaugruppe Easy

TVR	–	D	/	200	/	D2	/	Easy
\|		\|		\|		\|		\|
1		2		5		6		7

1 Type
TVE VAV terminal unit

2 Acoustic cladding
No entry: none
D With acoustic cladding

3 Material

5 Nominal size [mm]
100

125

160
200
250

315
400

6 Accessories

No entry: none

D2 Lip seals on both ends
G2 Matching flanges for both ends

7 Attachments (control components)
Easy Easy controller

Order example: TVE-D/125/D2/Easy

Acoustic cladding	With
Material	Galvanised sheet steel
Nominal size	125 mm
Accessories	Double lip seal both ends
Attachment	Easy controller

Variants

Easy controller TR0VE-024T-05I-DD15

1: Easy controller
2: Release button and damper blade position indicator
3: q_vminpotentiometer
4: q_vmaxpotentiometer
5: 'Test' push button and LED for indicating the operating states
6: Terminals

Easy controller type 1 with positive lock

Easy controller type 1 with clamping device

Easy controller type 2 with positive lock

Easy controller type 2 with clamping device

Product details, Technical Data

Select nominal size

Commissioning

Take the adjustment values from the volume flow rate scale (sticker on each VAV terminal unit)
Use the potentiometer to set the minimum or maximum volume flow rate on site
Comply with the volume flow rate control range, do not set a volume flow rate which is below the minimum flow rate
Volume flow rate control range TVE: 4 – 100%
Volume flow rate range of LVC, TVR, TZ-Silenzio, TA-Silenzio, TVZ and TVA: 10 – 100%
Volume flow rate range of TVJ and TVT: 20 – 100%
Once the VAV terminal unit has been installed and wired, and the volume flow rate has been set, the unit is ready for operation
Remove the protective cap or terminal cover (TVE) of the Easy controller only temporarily for wiring and commissioning

Description of status LEDs and error messages regarding control components for terminal unit TVE

LED pushbutton flashing signal	Flashing signal in words	Status
	LED off	No voltage
	LED blinks 4 times briefly within 2 seconds.	Call the TROX Technical Service
	LED blinks 3 times briefly within 2 seconds.	Actuator overload detected
	LED blinks once briefly within 2 seconds.	Synchronisation in progress (after Power up)
	LED blinks once briefly within 2 seconds.	Test mode is active
	LED blinks twice briefly within 2 seconds.	Overpressure detected by sensor
	LED blinks once (long) within 2 seconds.	Setpoint value or required position (override) not yet reached
	LED remains on.	Regulated. Signalled as long as the actuator does not rotate to readjust the setpoint value
	LED blinks twice (long) within 2 seconds.	Required position (override) has been reached

The flashing signal appears every 2 seconds. 1 = LED is illuminated, 0 = LED is not illuminated

Starting a test run for control components on VAV terminal units type TVE

Pressing the LED push button for > 2 s starts a test run.

Description of status LEDs and error messages regarding control components for terminal units LVC, TVR, TVJ, TVT, TZ-Silenzio, TA-Silenzio, TVZ and TVA

LED	Operating status
OFF	No power Easy controller faulty
ON	Flow rate setpoint value has been reached
Blinking slowly (0.5 Hz)	Actual value ≠ setpoint value Controller is trying to achieve the setpoint or Test in progress Synchronisation in progress
Blinking rapidly (2.5 Hz)	Direction of rotation has been changed

Easy controller LMV-D3LA-F

Volumenstromsollwert_0-10V_fo_01pdf.pdf.link

Volumenstromistwert_0-10V_fo_01pdf.pdf.link

Easy controllers for VAV terminal units

VAV terminal units	Type	Part number
LVC	LMV-D3AL-F TR	M466EU1
TVE	TR0VE-024T-05l-DD15	A00000069228
TVR	LMV-D3A-F TR	M466ES1
TVR	227V-024T-05-002	M466DC3
TZ-Silenzio, TA-Silenzio, TVZ, TVA	LMV-D3A TR	M466ES2
TZ-Silenzio, TA-Silenzio, TVZ, TVA	227V-024T-05-002/RE20	A00000089738
TVJ and TVT up to 1000 × 500	227V-024T-15-002	A00000053055
TVT from 1000 × 600	SMV-D3A TR	M466ES3

Easy controller LMV-D3AL-F TR for VAV terminal unit LVC

Supply voltage (AC)	24 V AC ± 20 %, 50/60 Hz
Supply voltage (DC)	24 V DC -10/+20 %
Power rating (AC)	3.5 VA max.
Power rating (DC)	2 W max.
Run time for 90°	120 – 150 s
Setpoint value signal input	0 – 10 V DC, Ra > 100 kΩ
Actual value signal output	0 – 10 V DC, 0.5 mA max.
IEC protection class	III (protective extra-low voltage)
Protection level	IP 20
EC conformity	EMC to 2014/30/EU, low voltage to 2014/35/EU

Easy controller TR0VE-024T-05I-DD15 for VAV terminal unit TVE

Supply voltage (AC)	24 V AC ± 20 %, 50/60 Hz
Supply voltage (DC)	24 V DC ± 20 %
Power rating (AC)	NW 100 - 200: 4 VA max. / NW 250 - 400: 7 VA max.
Power rating (DC)	NW 100 - 200: 2.5 W max. / NW 250 - 400: 4 W max.
Power consumption (when running/when idle)	1 W
Run time for 90°	100 s
Setpoint value signal input	0 – 10 V DC, Ra > 100 kΩ
Actual value signal output	0 – 10 V DC, 0.5 mA max.
IEC protection class	III (protective extra-low voltage)
Protection level	IP 42 (with the terminal cover attached)
EC conformity	EMC to 2014/30/EU

Easy controller LMV-D3A TR for VAV terminal unit LVC

Easy controller LMV-D3A(-F) TR for VAV terminal units TVR, TZ-Silenzio, TA-Silenzio, TVZ and TVA

Supply voltage (AC)	24 V AC ± 20 %, 50/60 Hz
Supply voltage (DC)	24 V DC -10/+20 %
Power rating (AC)	5 VA max.
Power rating (DC)	2.5 W max.
Run time for 90°	110 – 150 s
Setpoint value signal input	0 – 10 V DC, Ra > 100 kΩ
Actual value signal output	0 – 10 V DC, 0.5 mA max.
IEC protection class	III (protective extra-low voltage)
Protection level	IP 20
EC conformity	EMC to 2014/30/EU

Easy controller 227V-024T-05-002(/RE20) for VAV terminal units TVR, TZ-Silenzio, TA-Silenzio, TVZ and TVA

Supply voltage (AC)	24 V AC ± 20 %, 50/60 Hz
Supply voltage (DC)	24 V DC ± 20 %
Power rating (AC)	5 VA max.
Power rating (DC)	3 W max.
Run time for 90°	100 s
Setpoint value signal input	0 – 10 V DC, Ra > 100 kΩ
Actual value signal output	0 – 10 V DC, 0.5 mA max.
IEC protection class	III (protective extra-low voltage)
Protection level	IP 20
EC conformity	EMC to 2014/30/EU

Easy controller SMV-D3A TR for VAV terminal unit TVT from NW 1000 x 600

Supply voltage (AC)	24 V AC ± 20 %, 50/60 Hz
Supply voltage (DC)	24 V DC -10/+20 %
Power rating (AC)	6 VA max.
Power rating (DC)	3 W max.
Run time for 90°	110 – 150 s
Setpoint value signal input	0 – 10 V DC, Ra > 100 kΩ
Actual value signal output	0 – 10 V DC, max. 0.5 mA
IEC protection class	III (protective extra-low voltage)
Protection level	IP 20
EC conformity	EMC to 2014/30/EU

By clicking the button, you allow us to provide you with an excellent website experience and easy shopping processes. These cookies include ones that are necessary for the operation of the site and for the control of our services and applications, as well as ones that are used solely for statistical purposes, for convenience settings or to display personalized content. You can decide which categories you want to allow and you can adjust the data utilisation settings based on your individual requirements. Please note that, depending on the settings that you have selected, all functionalities of the page might not be available. You can change your selection at any time.

TECHNICALLY NECESSARY

These cookies are necessary for the proper functioning of our website and cannot be disabled. As a rule, these cookies are set only in response to actions taken by you, such as setting your privacy preferences or filling the shopping cart. In addition, security-relevant functionalities or support via a dedicated webchat are integrated, including all session cookies from TROX set after you log in as a customer. You can set your browser to block these cookies or notify you about them. As a result, however, some areas of the website might not function as intended.

EASY